Open WRT OR DD WRT for Home Hub 2.0?

[Detection]

Hey guys took the risk and tried the experimental version, had a few problems but sorted them, but I've got to the point where it's on the device and working fine apart from opkg update doesn't work, comes back saying failed to download http://downloads.openwrt.org/snapsho...es/packages.gz wget returned 1
any ideas?
Jamie

Because that link is dead ?


I've been playing with my DDWRT router and there was a similar issue, had to update the opkg.conf with a new working repository link

Your link works, but that packages.gz is not a valid file, it seems only a capital letter is breaking it, it should be Packages.gz

working

http://downloads.openwrt.org/snapsho...es/Packages.gz

[daemon123]

Hi,
sorry for posting here, but i think it will be better,
i have a dead (tried to jtag several times, but no luck) BT HH 2 Type A, have pulled out the mini pci wifi. I would like to use it in my old WRT54G v 1.0 as it has mini pci slot, i can compile openwrt firmware for it but i dont know which type of wifi to choose in there, if anyone you get the wifi bg and n working then post here the type of wifi to select.
Thx.

[danitool]

About the BCM5325 switch, I've traced some pins at my board livebox.

I guess the pin connected directly to the nTRST, at the SoC, should be the RESET pin at the switch. I'm not sure the pinout posted at the Pudeev site is right.

bcm5325_sp.jpg

[danitool]

I'll answer myself. I didn't notice the pudeev pinout is from a circuit schematic, that was confusing me, the pins number is totally correct, but not the place. I've made another draw with the pins in its right place:

http://wiki.openwrt.org/_media/toh/bcm5325_pinout.png

Yes, the pin 128 is RST_N, and it must be pulled high, either with a gpio or else via pullup resistor. I wonder why the pin 8 SS# is connected to a GPIO in the livebox pro, since it's a SPI pin.

[raidersan]

Guys, apologies for the stupid question, but I have just put a JTAG on my HH2.0A to downgrade from a H.U firmware, will I need this JTAG to go to OpenWRT (hopefully soon?) , or will it be flash-able without the JTAG?
I also now have a 2.0B, I will donate one of them, which one should I keep for installing OpenWRT on?
Thanks in advance

[jamidodger1]

Guys, apologies for the stupid question, but I have just put a JTAG on my HH2.0A to downgrade from a H.U firmware, will I need this JTAG to go to OpenWRT (hopefully soon?) , or will it be flash-able without the JTAG?
I also now have a 2.0B, I will donate one of them, which one should I keep for installing OpenWRT on?
Thanks in advance

It works without JTAG like the unlocking method, I know it works on 2.0A because thats the one I have, but not sure on the 2.0B...

[jamidodger1]

How do I do a factory reset?
Seem to of messed up LAN settings so now no access to the router :/
Button on side doesn't seem to work either
Thanks
Jamie

[Detection]

How do I do a factory reset?
Seem to of messed up LAN settings so now no access to the router :/
Button on side doesn't seem to work either
Thanks
Jamie

Press the pin hole reset button for 30 seconds while it is turned on, keep it pressed and unplug the power keeping the button pressed for another 30 seconds, then keep the reset button pressed and plug power back on for another 30 seconds then you can release the reset button

This is called the 30/30/30 reset

[jamidodger1]

Hm I think I tried that but ill have another go in a while, but the button push reset does nothing normally so will it acturally work? I've messed up LAN / wan settings do the broadband light that i set up earlier has gone out, can't acess the router via LAN, will there ever be WLAN support for it?ThanksJamie

[raidersan]

Googling around I read some mentioning that they have the 2.0A & OpenWRT working, but I assume this thread is the ultimate source on the topic. From what I understand it is not yet fully functional, contradicting those other posts. Can somebody confirm the current state and what to expect next?
Many thanks to all the guys working hard on this!